Reflective Polished Concrete Floors for Laval Homes
Transform your slab into a hard, gleaming surface that requires only damp-mopping to maintain. Laval Concrete grinds, densifies, and polishes your existing concrete to satin or high-gloss, creating a finish that lasts decades without recoating.
When you polish concrete, you are not applying a layer on top. The slab itself becomes the finished surface, ground finer and finer until it reaches the gloss you want. There is nothing to peel, chip, or strip away later.
Our process uses diamond grinding to expose the aggregate and matrix, then a chemical densifier locks the surface into a hard, tight structure. From there, we continue polishing through progressively finer grits. Satin finishes land around 400 grit; full mirror-gloss can reach 3000 grit or higher.
Maintenance is straightforward: a damp mop once a week keeps it clean. No carpet to replace, no grout lines to scrub, no recoating cycle every few years. Our full floor lineup includes stained finishes and epoxy coatings for different needs, but polished concrete stands alone for durability.
Recent work
The sequence
Polishing a Concrete Floor Step by Step
Assess slab readiness
We measure moisture content, check for cracks or cold joints, and identify any old coatings that need removal. A sound slab is the foundation for a polished finish.
Grind and densify
Diamond tooling grinds the surface progressively finer, exposing the concrete matrix. A chemical densifier is applied to harden the top layer and reduce porosity.
Polish to your gloss
We continue grinding through finer grits until reaching your chosen finish: soft satin, semi-gloss, or high-gloss mirror. Stain protection is added where needed.
Final cure and handoff
The densifier and sealer cure on schedule. A final buff brings out clarity and shine. You receive care instructions for damp-mopping and routine maintenance.
Choosing the right floor
Polished vs Epoxy, Stain, Micro-Topping
Polished concrete and epoxy coatings are the two main interior choices. Polished is the slab itself, permanent and never needs recoating. Epoxy is a seamless coating that offers more colour and pattern variety but requires recoating over time.
Stained concrete adds colour by working dye into the slab, often paired with a polished or sealed finish. Micro-topping is a thin overlay that prepares an unsuitable slab for polishing. Self-leveling underlayment corrects flatness issues before any finish is applied.
Gloss levels, slab conditions, density and maintenance for polished floors in Laval.
Most can, but the slab condition decides the finish. We test for moisture, cracks and old coatings first. Slabs with surface damage may need a micro-topping first to give the polish a clean canvas.
From a soft satin (around 400 grit) to a mirror-like high-gloss (3000 grit and beyond). The gloss level is your choice; we grind through the right number of passes to reach it.
Sealed properly with a stain-protector, polished concrete resists stains well. Spilled wine or oil should still be wiped up promptly, but the densified surface is far less porous than untreated concrete.
Concrete temperature follows the room, so it is no colder than tile or stone in the same conditions. Pair it with heated floor underlayment if you want warmth underfoot.
Decades, with basic damp-mop maintenance. There is no coating to fail and no surface to wear off; the polish is the slab itself, densified into a hard matrix that holds up to daily life.
Homeowner reviews
What Laval Homeowners Say About Their Polished Floors
Polished the whole main floor after the kitchen reno. The reflectivity makes the whole room look bigger and the maintenance is just a damp mop once a week.
I. S.
Laval
★★★★★
Picked a satin gloss level instead of full high-gloss for the basement. Soft underfoot look, hard as can be, and the kids' toys roll cleanly across it.
U. M.
Terrebonne
★★★★★
They tested the slab first and recommended a micro-topping before polishing because of some surface cracks. Saved us from a polish-over-cracks disaster, exactly the right call.
E. O.
Longueuil
★★★★★
Stain protector is doing its job. We have spilled coffee and red wine and both wiped up clean. Maintenance is way less than the hardwood we replaced.
G. F.
Montreal
From the blog
Concrete Guides & Articles
Practical reading on planning, finishes and caring for concrete in Laval.
Describe the room and your preferred gloss level, satin to high-gloss, and we will evaluate the slab, recommend the right approach, and provide a written, itemised quote.
